For VME bus, users themselves could design interface circuit according to particular demand such as only slave interface. 对于VME总线,用户可以根据特定要求自行设计接口电路,比如只实现从模块访问。
Aiming at airborne equipments with PC104 form computer systems, this paper presents a method of using FPGA to realize the special chip for the bus interface circuit design. 本文针对采用PC104构建计算机系统的机载产品,提出了采用FPGA代替专用芯片进行总线接口电路设计的方法;
Design Of Field Bus Interface Circuit 现场总线接口电路的设计
It includes VXI bus interface designing, serial communication circuit designing, interface driver circuit designing and control logic designing. 通过VXI接口电路设计、串行通信电路设计、接口驱动电平设计和控制逻辑设计,实现设计功能要求;
Input circuit, output circuit, and bus interface circuit are designed. According to the characteristics of the control plant, the PWM is utilized to realize D/ A. 设计了输入、输出信号电路,总线接口电路,根据控制对象的特点,采用PWM实现D/A转换。
One integrated implementation method for 32-bit VXI bus interface circuit design 一种32位VXI总线接口电路的集成化设计方法
The paper introduces an image collecting system based on universal serial bus ( USB) interface. The elaborated circuit firmware program and device-driving program are given. 讨论了一种基于通用串行总线(USB)的图像采集系统的实现,给出了系统的硬件电路、设备固件程序及设备驱动程序。
The Computer PCI Bus& the Design of Its Interface Circuit 计算机PCI总线及其接口电路的设计
In order to enhance the reliability of optical fiber CAN network, a reliable dual ring optical fiber CAN network with protective ring and relevant fiber-CAN bus interface circuit are designed. 为提高光纤CAN网络的可靠性,设计了高可靠性带有保护环的光纤双环CAN网络以及相应的fiberCAN总线接口电路。
Design of a Slave I~ 2C Bus Interface Circuit and Its VLSI Implementation 从模式I~2C总线接口电路设计及其VLSI实现
The design of CAN bus hardware interface circuit based on SJA1000, the selection of chips, the design of software and the realization of CAN communication are expatiated. 论述了基于SJA1000的CAN总线的硬件接口电路的设计、芯片的选择、软件设计及CAN通信的实现。
PCI Bus and Its Interface Circuit Design PCI总线接口电路设计
There will be no place for ISA Bus after the vanish of ISA slots on computer mainboard. So the interface circuit design based on PCI Bus is presented in this paper. 以及计算机主板的ISA插槽在逐渐的消失,所以本文又提出设计基于PCI总线的接口电路。
An Effective Method for Migrating ISA Bus Interface Circuit to PCI Bus 将ISA接口卡移植到PCI总线的高效设计方法
The PCI bus protocol is so intricacy, however, that there's more difficulties in realizing the interface than ISA bus, and it's hard to design the appropriate digital logic interface circuit for PCI. 但是PCI总线协议十分复杂,其接口的实现比ISA困难地多,直接为它设计相匹配的数字逻辑控制电路难度很大。
In addition during transmitting the wave, the power energy to supply bus interface circuit is simultaneously delivered, therefore, the demand for bus isolation or float is met, and the common mode disturbance is effectively rejected. 另外,可利用长线传输波形的同时,还传输供总线接口电路需要的电源能量,满足总线浮空隔离的要求,有效地抑制了共模干扰。
This technology is especially suitable for bus interface circuit. 这对总线接口电路尤其实用。
As for the part of software, Current and voltage zero cross detection circuit, synchronism signal detection circuit, Current and voltage detection circuit and CAN bus interface circuit and so on are designed. 硬件部分主要对电流电压检测电路,同步信号检测电路,电流电压过零检测电路,CAN总线接口电路等进行了设计。
Hardware equipped with the ultrasonic transceiver circuits, power circuits, temperature compensation circuit, USB bus interface circuit, and also extends the keyboard, LCD display human-machine interface. 硬件方面配有超声波收发、电源、温度补偿、USB总线接口等电路,同时还扩展了键盘、LCD显示人机接口。
The system connect IIC bus of digital tuner and parallel port of PC with interface circuit. 硬件上利用接口驱动电路实现PC并口与数字调谐器的I2C总线的连接。
Then designed the various communication interface circuits; such as CAN bus interface circuit and USB interface circuit. 根据通信方式的不同,分别设计了CAN总线接口电路、USB接口电路和无线接口电路。
Signal acquisition system designed hardware circuitry and software workflow, and analysis of the system bus, given the system interface circuit related. 设计了信号采集系统的硬件电路及其软件工作流程,并分析了系统总线,给出系统相关的接口电路。
The system consists mainly of measuring circuit, the microprocessor system, alarm circuit, 232 bus interface circuit, display circuit, storage circuit and power circuit. 该智能传感器主要由测量电路、微处理器系统、存储电路、显示电路、报警电路、232总线接口电路和电源电路组成。
ISA bus interface control circuit was studied and designed to achieve communicate between peripheral equipment and PC. 为实现PC机和外围设备之间的通信,对ISA总线接口控制电路进行了研究与设计。
Design of the data transfer bus interface circuit is one of the key technologies in the new imaging logging system developed. 测井仪器通信总线接口电路的设计是新型成像测井系统研制的关键技术之一。
Thirdly, the hardware implementation of the card is described in detail, including MVB bus interface, ARM peripheral circuit, and the PCI interface. 接着详细叙述了网卡的硬件设计与实现,包括MVB总线接口、ARM外围电路以及PCI接口的设计。
It includes design of DSP periphery basic electric circuit, like power source, monitor of power source, replacement and simulation connection and so on. It also includes the input and output of motion control board, realization of VME bus interface electric circuit. 包括DSP外围基本电路的设计,如电源、电源监控和复位、仿真接口设计等;运动控制卡的输入和输出;VME总线接口电路的实现等。
According to the analysis and abstract of the software and hardware interface, the configuration circuit of FPGA includes these parts: configuration interface, configuration registers, bus decoder interface, and configuration control circuit. 通过对FPGA的软硬件接口环境的分析和抽象建模,本文提出的配置电路包含配置接口电路,配置寄存器,总线译码部分和配置电路控制模块。